Confirm your hose before anything else
The MaxiMist Elite Series Pro Spray Tanning Gun ST301 connects with a male Quick Connect fitting. It will work with any spray tanning system hose that has a Quick Connect fitting, but it will not work with other hose types. Before you unpack the gun or plan your first tan, check that your hose ends in a matching Quick Connect coupler. If your hose uses a different connection, this gun is not the right fit for your setup.
What the ST301 includes and why it matters for setup
- MaxiMist Elite Series Pro Spray Tanning Gun ST301: Connection: Male Quick Connect This is the single compatibility point that determines whether the gun will attach to your existing hose.

MaxiMist Elite Series Pro Spray Tanning Gun ST301 - MaxiMist Elite Series Pro Spray Tanning Gun ST301: Includes 3 additional cups with lids, 3 additional cup gaskets, needle spring, extra gland seal, duckbill with clip, air tubing, pick-up tube, spray gun lubricant, cleaning brush, spanner tool, and hex wrench. These parts support assembly, maintenance, and spare-part replacement, so you can set up and care for the gun without sourcing extras immediately.
- MaxiMist Elite Series Pro Spray Tanning Gun ST301: Cup: 8oz; Tip and Needle: Stainless 0.5mm; Weight: 2 lbs. The 8 oz cup sets your solution capacity per fill, while the 0.5 mm stainless tip and needle are the fluid path components you will handle during cleaning and assembly.
Assemble the gun for first use
The supplied information lists the included components and the air adjust knob but does not provide a full step-by-step assembly sequence. The steps below reflect only what the record supports; consult the manufacturer's instructions for any detail not covered here.
- Attach the cup and gasket: Seat one of the 8 oz cups with its lid and cup gasket on the gun. The record includes three additional cups with lids and three additional cup gaskets, so you have spares for multiple solutions or replacement needs.
- Connect the air tubing and pick-up tube: The record lists air tubing and a pick-up tube among the included parts. These are the components that link the gun to your air supply and draw solution from the cup.
- Fit the duckbill with clip: The duckbill with clip is included. It is part of the gun's air and fluid delivery assembly; install it according to the manufacturer's diagram if one is provided.
- Check the air adjust knob: The air adjust knob is the supplied control for regulating airflow. The record does not specify a starting setting, so begin with the manufacturer's recommendation or test on a practice surface before spraying a client.
- Attach the gun to your Quick Connect hose: Push the male Quick Connect fitting on the gun into the matching coupler on your hose until it seats. Confirm the connection is secure before adding solution.
The EZ Flip dial and what it changes
The ST301 includes an EZ Flip airbrush mode dial, which the catalog describes as being for contouring, bikini lines, and similar detail work. This is a mode control, not a separate tool. For a first session, set the dial to your standard spray mode for broad coverage, then switch to the detail mode only when you reach areas that need finer control. The record does not specify which dial position corresponds to which mode, so label or note the positions during your first practice run.
First-use checkpoints before you spray a client
- Hose connection is secure: The gun must be fully seated on a Quick Connect hose. A partial connection can affect airflow and spray consistency.
- Cup and gasket are seated: A misaligned gasket can cause solution to seep or the cup to sit unevenly. Check that the lid and gasket are flush before filling.
- Air adjust knob is at a known starting point: Because the record does not give a default setting, mark or note your starting position so you can return to it after testing.
- Practice on a surface or mannequin first: The supplied information does not include a spray pattern test protocol. A practice pass lets you confirm the gun is assembled correctly and the dial modes behave as expected before a live tan.
What the supplied information does not cover
The record does not provide a complete assembly diagram, a specific air pressure setting, a cleaning procedure, or a troubleshooting chart for the ST301. It also does not confirm whether the gun is compatible with every solution brand or viscosity. For those details, rely on the manufacturer's documentation or contact the dealer. The ST301 is sold as brand new with the full manufacturer warranty through an authorized MaxiMist dealer, so keep your purchase record for any warranty questions.


