Norvell iNTELLISPRAY Clear Plus: Booth Solution Usage Guide
By Sun Tanning Store | Published: 2026-10-31
Category: How-to Guides
A step-by-step guide to setting up and running Norvell iNTELLISPRAY Clear Plus in a heated down-draft booth, with checkpoints to avoid common mistakes.
Quick answer
Use Norvell iNTELLISPRAY Clear Plus as a ready-to-use solution in a Norvell Auto Revolution booth, and do not dilute it unless Norvell's instructions for your exact booth model say otherwise. Load the 1.3-gallon container, prime the line, and run a test pass before your first client.
Why this solution is tied to a specific booth type
iNTELLISPRAY Clear Plus is formulated to work with the heated down-draft technology of the Norvell Auto Revolution. That means the booth's heat and airflow are part of how the solution performs, not just a comfort feature. If you run it in a different spray booth, you are guessing at dry time and color development.
The practical trade-off: this is not a universal booth solution you can move between any machine. Check that your booth is a Norvell Auto Revolution or a model Norvell lists as compatible before you buy the 1.3-gallon size.
What the catalog does and does not tell you
The product record confirms the built-in xLaTan prep spray and Ordenone odor-inhibiting ingredient, but it does not list a dilution ratio, a per-session volume, or a shelf life after opening. Those numbers have to come from Norvell's instructions for your booth or from your own measured test runs.
Treat any dilution figure you see online as unverified until it matches the label or Norvell's documentation. Guessing a ratio is the fastest way to get uneven color or a clogged line.
Step-by-step setup and use
- Confirm booth compatibility: Check that your booth is a Norvell Auto Revolution or a model Norvell lists for iNTELLISPRAY Clear Plus. If it is not, stop and choose a solution matched to your booth instead. Write the booth model and serial number on your solution log so the next reorder is not a guess.
- Inspect and load the 1.3-gallon container: Check the seal and date, then load the container into the booth reservoir following the booth manual. Do not pre-mix with water or a separate prep spray unless the label says to. Record the open date on the container; without a listed shelf life, your own log is the only way to track age.
- Prime the line and check the spray pattern: Run the booth's prime cycle, then spray a test pass onto a white towel or paper. Look for an even, fine mist with no spitting or gaps. If the pattern is uneven, clean the nozzle before your first client rather than adjusting the solution.
- Run one test tan before a full appointment: Spray a test patch or a staff volunteer and note dry time, color development, and any odor. Compare against your previous solution so you know what changed. Keep the test result with the open date; it becomes your baseline for the rest of the container.
- Set a cleaning and storage routine: Flush the line per the booth manual after each session day, and store the container sealed at the temperature the label specifies. Do not leave solution sitting in the line overnight. A daily flush is cheaper than a clogged line, especially when you cannot verify a post-opening shelf life.
Product facts
- Norvell iNTELLISPRAY (Clear Plus) Premium Booth Solution 1.3 gallon: 1.3-gallon container of Norvell iNTELLISPRAY Clear Plus, formulated for the Norvell Auto Revolution heated down-draft booth. Buy the size that matches your booth's reservoir and session volume, and confirm booth compatibility before ordering.
Norvell iNTELLISPRAY (Clear Plus) Premium Booth Solution 1.3 gallon - Norvell iNTELLISPRAY (Clear Plus) Premium Booth Solution 1.3 gallon: Blended with xLaTan prep spray and Ordenone odor-inhibiting ingredient. The prep step is already in the solution, so adding a separate prep spray can over-apply and change results.
