Torna al blog
Guide pratiche 2026-11-20 Sun Tanning Store 0 visualizzazioni

How to Replace Your Tanning Bed Lamp Holder

How to Replace Your Tanning Bed Lamp Holder

Learn how to safely replace a tanning bed lamp holder, including compatibility checks and step-by-step guidance for SunDome and ProSun models.

Why Lamp Holder Replacement Matters

Lamp holders hold your tanning bed lamps in place and keep the electrical connection secure. Over time, heat and UV exposure can make them brittle or cause the contacts to loosen. A faulty holder may cause flickering lamps, uneven tanning, or even a short circuit. Replacing them early keeps your bed running reliably.

Check Compatibility Before You Buy

Not all lamp holders fit every bed. You need to match the holder type and quantity to your specific model. Here is how to confirm the right part.

  1. Identify your bed model: Check the manufacturer label on your tanning bed frame or canopy. For example, the ProSun Onyx series uses a specific plastic lamp holder (Model # M-13, Part # ELEC3502205). SunDome XL48 beds require a complete kit with 48 bi-pin lamp holders.
  2. Count the lamps and holders: Your bed may use a different number of holders than another model. The SunDome XL48 kit includes exactly 48 holders with starter sockets, which matches the XL48's lamp configuration. If you are replacing just a few, buy individual holders that match your bed's original part number.
  3. Choose between individual holders or a kit: For a full bed reconditioning, a kit saves time and ensures all holders match. For a single broken holder, buying one replacement is more economical. The ProSun Onyx Lamp Holder is sold individually, while the SunDome XL48 kit gives you everything in one package.

Tools and Safety Prep

Before you open the bed, unplug it from the power source. Tanning beds use high voltage, and working on them while plugged in is dangerous. You will need a screwdriver (usually Phillips head), a pair of needle-nose pliers, and possibly a small flathead screwdriver to release old wire terminals. Wear gloves to protect your hands from sharp edges inside the bed.

Step-by-Step Replacement

Follow these steps carefully. If you are unsure at any point, consult a professional technician.

  1. Remove the acrylic shield and lamps: Take out the acrylic panel that sits over the lamps. Then gently remove each lamp by twisting it out of its holder. Place lamps on a clean, soft surface to avoid breakage.
  2. Release the old lamp holder: Locate the holder you are replacing. It is usually clipped or screwed into the bed frame. Use your screwdriver to remove any screws, then gently pry the holder loose. Note how the wires connect before disconnecting them—take a photo if helpful.
  3. Disconnect the wires: Use pliers to pull the wire terminals off the holder's spade connectors. Do not pull on the wire itself; grip the terminal. If the holder has a starter socket (like the bi-pin holders in the SunDome kit), remove the starter separately.
  4. Install the new holder: Push the wire terminals onto the new holder's spade connectors. Make sure they are snug. Then clip or screw the new holder into the bed frame. Confirm it is secure and straight.
  5. Reinstall lamps and acrylic: Insert each lamp into its new holder, twisting to lock. Replace the acrylic panel and secure it. Plug the bed back in and test by turning it on briefly. If all lamps light evenly, the replacement is successful.

Product Evidence for This Job

  • SunDome XL48 Lamp Holder Replacement Kit (Premium): Complete SunDome XL48 Lamp Holder Replacement Kit includes 48 bi-pin lamp holders with starter sockets. If you own a SunDome XL48 bed, this kit gives you every holder you need in one order, saving you from buying individual parts.
    SunDome XL48 Lamp Holder Replacement Kit (Premium)
    SunDome XL48 Lamp Holder Replacement Kit (Premium)
  • ProSun Onyx Lamp Holder: ProSun Onyx Lamp Holder (Model # M-13, Part # ELEC3502205) is a replacement plastic lamp holder for all ProSun Onyx tanning units. For ProSun Onyx owners, this single holder is the correct part for spot replacements. Confirm your bed uses the M-13 model before ordering.
    ProSun Onyx Lamp Holder
    ProSun Onyx Lamp Holder

What to Do If You Are Unsure

The supplied product information confirms compatibility for specific models, but it does not list every bed that uses these holders. If your bed is not a SunDome XL48 or a ProSun Onyx, check your owner's manual or contact the manufacturer to verify the holder type. Replacing a holder with the wrong part can damage the bed or create a fire risk.

Articoli correlati

Customer Service
Home
Prodotti
Carrello
Profilo